Alamo Industrial Mower Dealer in Central New York

Showing all 21 models

Alamo Industrial boom mower

Alamo Industrial Machete 3

Side-mount boom with a closed-loop piston pump and motor system that runs cooler than a gear system.

18–25 ftboom lengths

90engine HP min.

120°front to back swing

• Closed-loop piston pump and motor system
• Joystick control is standard
• Four-bar design gives 215° head rotation
• Cast king post mount with greaseable, hardened steel bushings
• Two-piece boom rest for transport and storage

Full specifications

Boom Lengths	18 ft, 22 ft, & 25 ft
Tractor Requirement	CAB; 90 engine HP, 90 in wheelbase, 8500 lbs shipping weight, 18 in ground clearance
Cutting Head Options	Severe Duty Rotary, Flail-Axe®, Heavy Duty Grass Flail, SRD, Ditcher, BuzzBar®, Timbercat
Hydraulic System	Tandem front hydraulic pumps. Closed-loop piston pump and motor system.
Joystick	Included

Source: Alamo Industrial Machete 3 page.

Alamo Industrial boom mower

Alamo Industrial Samurai

The maker's most cost-effective boom, made for municipal mowing over guardrails and barriers.

18–25 ftboom lengths

80engine HP min.

85 inwheelbase min.

• King post style turning arm
• Self-contained hydraulic circuit for head and boom
• Front-mounted hydraulic reservoir
• Manual cable or lever controls, optional joystick

Full specifications

Boom Lengths	18 ft, 22 ft, & 25 ft
Tractor Requirement	CAB; 80 engine HP, 85 in wheelbase, 6,000 lbs shipping weight
Cutting Head Options	Severe Duty Rotary, Flail-Axe®, Heavy Duty Grass Flail, SRD, Ditcher, BuzzBar®, Timbercat
Hydraulic System	Self-contained hydraulic circuit for both mowing head and boom control, a front-mounted hydraulic reservoir for improved visibility, safety, and operator access
Joystick	Manual cable or lever controls, optional joystick

Source: Alamo Industrial Samurai page.

Alamo Industrial boom mower

Alamo Industrial Maverick 2

Heavy side-mount boom built like a backhoe arm, with a 180° turret swing and up to 30 ft of reach.

24–30 ftboom lengths

180°front to back swing

110engine HP min.

• Turret-style mount with 180° hydraulic swing
• Mows within 6” of the tire
• Closed-loop piston pump runs cooler
• Four bar linkage reaches hard-to-reach angles

Full specifications

Boom Lengths	24 ft, 28 ft (Fixed Dipper), and 30 ft Models (3 ft. telescopic is included in full length)
Tractor Requirement	CAB; TIV-B Models: 110 engine HP, 101 in wheelbase, minimum of 10,800 lbs shipping weight.
Cutting Head Options	Severe Duty Rotary, Flail-Axe®, Heavy Duty Grass Flail, BuzzBar®, SRD, Ditcher, Timbercat
Joystick	Included

Source: Alamo Industrial Maverick 2 page.

Alamo Industrial boom mower

Alamo Industrial RM Series (RM165 / RM180)

Rear-mount booms that are completely self-contained and use no tractor hydraulics.

18 ft 1 inlongest boom

4 inmax. vegetation diameter

58–65PTO HP min.

• No tractor hydraulics needed
• Cuts grass, brush and limbs up to 4 in
• Category II three-point hitch mount (RM180)
• Integrated parking stands for off-season storage (RM180)

Full specifications

Models	RM165 / RM180
Boom Lengths	16 ft 4 in or 18 ft 1 in
Cutting Head Options	48 in Heavy Duty Flail, 48 in Medium-Duty Rotary, 60 in Heavy Duty Rotary, 69 in BuzzBar®
Tractor Requirement	RM165: CAB; 58 PTO horsepower, 6,615 lbs shipping weight, 540 rpm PTO output shaft. / RM180: CAB; 65 PTO horsepower, 7,715 lbs shipping weight, 540 rpm PTO output shaft.

Source: Alamo Industrial RM Series page.

Alamo Industrial boom cutting head

Alamo Industrial Flail-Axe

Flail head with 16 anvil style flail blades, for cutting up to 4 in diameter.

4 incutting capacity

16anvil flail blades

995 lbsweight

• 16 anvil style flail blades
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Cutting Capacity	4 in diameter
Blades	Equipped with 16 anvil style flail blades
Weight	995 lbs
Dimensions	57.5 in W x 35 in D x 50 in H
Available for	Machete™ 3, Maverick™ 2, Samurai™

Source: Alamo Industrial Flail-Axe page.

Alamo Industrial boom cutting head

Alamo Industrial Severe Duty Rotary head

Rotary boom head in 50 in and 60 in sizes for brush up to 5 in.

5 incutting capacity

50 / 60 inmodels

• Full-swinging, double-edged, tempered steel blades
• Blades installed in matched sets
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Cutting Capacity	5 in diameter
Blades	Full-swinging, double-edged, tempered steel blades installed in matched set
Weight	50 in model: 1,050 lbs. / 60 in model: 1,195 lbs.
Dimensions	50 in model: 64 in W x 65 in D x 33 in H / 60 in model: 69 in W x 74 in D x 33 in H
Available for	Machete™ 3, Maverick™ 2, Samurai™

Source: Alamo Industrial Severe Duty Rotary head page.

Alamo Industrial boom cutting head

Alamo Industrial Heavy Duty Grass Flail head

Grass flail head with 40 pairs of replaceable blades.

2 incutting capacity

40pairs of blades

965 lbsweight

• 40 pairs of replaceable blades
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Cutting Capacity	2 in diameter
Blades	40 Pairs of replaceable blades (7 oz. models)
Weight	965 lbs
Dimensions	68 in W x 37 in D x 35 in H
Available for	Machete™ 3, Maverick™ 2, Samurai™

Source: Alamo Industrial Heavy Duty Grass Flail page.

Alamo Industrial boom cutting head

Alamo Industrial Ditcher head

Heavy duty rotary ditcher for clearing dirt and vegetation from roadway ditches, dry waterways and fire breaks.

22 inditch width

11 inditch depth

3blades

• Clears roadway ditches, dry waterways and fire breaks
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Clearing Width	Capable of clearing a ditch 22 in wide
Clearing Depth	Capable of clearing a ditch 11 in deep
Blades	Three blades, each 3/4 in x 9 in x 5-1/2 in
Dimensions	41 in L x 39 in W x 31 in H
Available for	Machete™ 3, Maverick™ 2, Samurai™

Source: Alamo Industrial Ditcher head page.

Alamo Industrial boom cutting head

Alamo Industrial SRD-50 head

Drum mulching head that cuts brush up to 8 in and grinds it into mulch on the ground.

50 incutting width

8 incutting capacity

18knife tools

• Reinforced drum with carbide fixed teeth
• Grinds cut material into mulch
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Cutting Width	50 in
Cutting Capacity	8 in diameter
Blades	Features Eighteen (18) individual, a cubit knife cutting tools
Available for	Maverick™, Machete™ and Samurai™ boom series

Source: Alamo Industrial SRD50 page.

Alamo Industrial boom cutting head

Alamo Industrial Timber Cat head

Cuts limbs like a hedge trimmer and drops the debris straight to the ground.

4 inlimb diameter

5 / 7 ftcutting widths

2,650 lbsshear force

• Two 5/8 in high strength alloy steel blades
• Clean cut for limb work in populated areas
• Fits Machete 3, Maverick 2 and Samurai

Full specifications

Cutting Capacity	4 in diameter tree limbs
Blades	Heavy-duty cutter bar is made of two 5/8 in thick blades constructed from high strength alloy steel
Cutting Width	5 ft & 7 ft
Power	2,650 lbs of force available to shear material
Available for	Machete™ 3, Maverick™ 2, Samurai™

Source: Alamo Industrial Timber Cat page.

Alamo Industrial boom cutting head

Alamo Industrial BuzzBar head

Saw head with 26 in circular blades that the maker says cuts as clean as a chainsaw.

26 incircular blades

4 incutting capacity

48–90 incutting widths

• Each blade has 60 teeth, set and filed
• 2, 3 or 4 blade versions
• Also fits the RM165/RM180 (69 in only)

Full specifications

Cutting Capacity	4 in diameter, each blade has 60 teeth that are set and filed
Blades	48 in (2-Blade) / 69 in (3-Blade) / 90 in (4-Blade)
Weight	650 lbs / 705 lbs / 800 lbs
Construction	The cutting head main channel made with one-piece formed 3/16 in steel coupled to 3/8 in steel endplate
Available for	Machete™ 3, Maverick™ 2, Samurai™, RM165/RM180 (69” only).

Source: Alamo Industrial BuzzBar page.

Alamo Industrial flail mower

Alamo Industrial Interstater

Flail mower system with side wings and a rear flail for wide, manicured cuts along highways and airport fields.

6 to 20+ ftcut in one pass

6”max. cutting height

1”cutting capacity

• Self-contained hydraulic system
• In-frame cooling
• Automatic wing shut-off in the raised position
• Super Heavy Duty rear flail in 74”, 88” or 96”

Full specifications

Cutting Width	6 feet to over 20 feet in just one pass
Cutting Capacity	Grass and brush cutting capacity: 1”
Cutting Height	Adjustable cutting height to 6”
Rear flail widths	74”, 88”, or 96”
Dual wing 16’5”	16’ 5” equipped with dual 62” side wings, 5,624 lbs
Dual wing 18’5”	18’ 5” equipped with dual 74” side wings, 5,624 lbs
Dual wing 20’9”	20’ 9” equipped with dual 88” side wings, 5,724 lbs

Source: Alamo Industrial Interstater page.

Alamo Industrial flail mower

Alamo Industrial Interstater Rear Mount

The Interstater flail system on a rear three-point mount, for a 23 ft cut with tractor versatility.

23 ftcutting width

120PTO or engine HP

5,500 lbsequipment weight

• Reversible, self-cleaning knives
• Cutting height 0 to 6 in
• Needs at least 3 quick disconnect valves
• Front counterweight required

Full specifications

Cutting Width	23 ft
Knives	Reversible & Self-cleaning
Overall Length	285.5 in
Weight	5,500 lbs
Cutting Height	0 in to 6 in, adjustable in .65 in increments
Tractor Requirement	120 PTO or Engine HP
Tractor weight	11,500 lbs
3-point lift	Minimum three-point lift capacity of 4,500 lbs
Quick Disconnect	Minimum of 3 quick disconnect valves
Counterweight	Front installed counterweight required for stability

Source: Alamo Industrial Interstater Rear Mount page.

Alamo Industrial flail mower

Alamo Industrial Super Heavy Duty flail

Category I rear-mount flail for a manicured look, sized for 25 to 50 PTO hp tractors.

74–96 incutting widths

25–50PTO hp

1”cutting capacity

• Category I three-point hitch mount
• Coarse, extreme service or fine cut knives

Full specifications

Cutting Width	74 in, 88 in, and 96 in
Cutting Capacity	1” diameter grass and weeds
Mounting	Category I three-point hitch mount
Tractor Requirement	25 - 50 PTO hp
Knife Weights	Coarse Cut – Standard, mounted, 3 oz / Extreme Service – Optional, 4 oz / Fine Cut – Optional, 2 oz

Source: Alamo Industrial Super Heavy Duty page.

Alamo Industrial flail mower

Alamo Industrial Versa Flail

Side-mount flail that floats over ground contours and throws cut material down, not out.

74 / 88”cutting widths

60engine hp min.

5/8”alloy steel blades

• Float control follows the ground to prevent scalping
• Self-contained gear pump hydraulics
• Side-mounted oil reservoirs, no oil cooler needed

Full specifications

Cutting Width	74” and 88”
Cutting Capacity	1” diameter grass and weeds
Durability	5/8” thick alloy steel blades
Tractor Requirement	60 engine hp, 80” wheelbase, 5,000 lbs shipping weight
Hydraulic System	Economical, self contained hydraulic system featuring gear pumps and motors, properly sized, side-mounted oil reservoirs maintain the proper oil temperature without the addition of costly oil coolers

Source: Alamo Industrial Versa Flail page.

Alamo Industrial flail mower

Alamo Industrial RoadMaster 1902S

Low maintenance rear-mount flail for verges, banks, canals and recreation parks.

72 incutting width

60 HPmin. PTO power

1,764 lbsweight

• 540 RPM PTO drive
• Made for verges, banks, canals and parks

Full specifications

Cutting Width	72 in
Tractor Requirement	60 HP
PTO Drive Shaft	540 RPM
Overall Width	71 in
Weight	1,764 lbs

Source: Alamo Industrial RoadMaster 1902S page (Min. PTO Power).

Alamo Industrial mower

Alamo Industrial Versa 60" and 72" Rotary

Side-mount rotary with float positions that let the head follow terrain contours.

60 / 72 incutting widths

1 incutting capacity

80engine HP min.

• Float positions follow ground contours
• Cuts vertically or horizontally
• Mid-mount frame interchanges with a flail, ditcher or boom

Full specifications

Cutting Width	60 in and 72"
Cutting Capacity	1 in diameter
Mounting	Multi-functional, mid-mount frame design allows the rotary mower to the interchange with a flail, ditcher, or boom mower cutting system
Tractor Requirement	80 engine HP, 85 in wheelbase, 6,000 lbs shipping weight

Source: Alamo Industrial Versa Rotary page.

Alamo Industrial mower

Alamo Industrial Falcon 15

Hydraulically driven wing rotary that stops the blades when the wings are raised.

10 / 15 ftcutting widths

3.5 incutting capacity

96 intransport width

• Hydraulic drive with automatic blade shutoff when wings are raised
• Self-level lift draw-bar hitch

Full specifications

Cutting Width	10 ft & 15 ft
Cutting Capacity	3.5 in diameter
Mounting	Mounts to tractors with a minimum 50 PTO HP and features a self-level lift draw-bar hitch design for uniform cutting
Tractor Requirement	75 HP
Transportation Width	96 in

Source: Alamo Industrial Falcon 15 page.

Alamo Industrial mower

Alamo Industrial Switch Blade sickle bar

Simple sickle bar mower that lets small tractors work the roadside.

5 / 6 ftcutting widths

90° / 75°tilt up / down

3,000 lbstractor weight min.

• Automatic, self returning breakaway
• Tilts 90° up and 75° down
• Optional Ag shoe and swath board

Full specifications

Cutting Width	5 ft and 6 ft
Cutting Capacity	.5 in diameter
Tilt Angle	The tilt angle of 90° up and 75° down
Safety	The unit features an automatic, self returning breakaway system that allows the cutter bar to hinge when obstructed
Tractor Requirement	Minimum Weight: 3,000 lbs
Optional Equipment	Knife holder brackets Ag shoe and swath board Pump guard kit special paint

Source: Alamo Industrial Switch Blade page.

Alamo Industrial TRAXX slope mower

Alamo Industrial TRAXX RC28

Lightweight rotary remote-control mower for grass and light brush on steep or unsafe ground.

28 hpengine

55°max. working angle

500 ftremote range

• Low center of gravity
• Rubber tracks
• Pre-set cut heights 1.2 to 7.1 in

Full specifications

Engine	28 hp
Working range	500 ft
Weight	1058 lbs.
Overall Length	59 in
Overall Width	59 in
Overall Height	30-36 in
Max Working Angle	55°
Cutting Width	43 in.
Pre-set cut heights	1.2 – 7.1 in.
Blade-tip speed	variable up to 205 mph
Tracks	Rubber
Axle to axle length	39.4 in.

Source: Alamo Industrial TRAXX RC28 page.

Alamo Industrial TRAXX slope mower

Alamo Industrial TRAXX RC75

75 hp remote-control flail mower for hazardous, confined and steep areas.

75 hpengine

55°max. working angle

1,200 lbattachment lift

• Closed circuit piston track and flail drives
• Self-tightening tracks
• Y-flails for grass and brush, J-flails for saplings

Full specifications

Engine	75 hp
Working range	500 ft
Weight	2,870 lb (Without Attachment)
Overall Length	90 in (Without Attachment)
Overall Width	51 in
Overall Height	41 in
Fuel Tank Capacity	10 gal
Max Working Angle	Rubber with Steel Cleats: Standard ~ max working angle 55° / Rubber: Optional ~ max working angle 40°
Cutting Width	51 in to 75 in
Attachment Lift Capacity	1,200 lb
Rotor speed	3,300 RPM
Cutting height range	.79 in. - 3.35 in. (5 positions)
Travel speed	0 - 2.2 mph (1st gear) / 0 - 4.3 mph (2nd gear)

Source: Alamo Industrial TRAXX RC75 page (rotor width as cutting width).

Nothing matches those filters. Clear filters

Options

Alamo Industrial lists these options and add-ons. Not every option fits every machine, so ask which ones suit the mower you are looking at.

• 

  Quick Hitch

  Alamo Industrial's quick attach system changes boom cutting heads in the shop or field in about ten minutes. It mounts with all Alamo Industrial hydro boom lines.

  Machete 3, Maverick 2, Samurai

Also available

• Optional joystick

  The Samurai comes with manual cable or lever controls; a proportional joystick is optional.

• Head swivel

  An optional head swivel on the Machete 3 reduces overall transport width.

• RM180 options

  An Axis-Cable control package in place of the electronic joystick, and a side gauge wheel kit for rotary heads.

• Interstater left wing remote positioner

  A left wing remote positioner is listed as an Interstater option.

• Switch Blade equipment

  Knife holder brackets, Ag shoe and swath board, and a pump guard kit.